Duratec Thermostat and Housing
Duratec Thermostat and Housing
£40.00
Mechanically controlled and replaces standard Mondeo Duratec item that is controlled by the Mondeo ECU.
Specification and Application
Component | Duratec Thermostat and Housing |
Type | Mechanical thermostat |
Engines | Ford 1.8 Duratec Ford 2.0 Duratec Ford 2.3 Duratec |
Applications | Kit Cars Rally/Race – MkI/II Escort, Sierra, Lotus Cortina BriSCA F2 Classic Ford |
Additional information
Weight | 1 kg |
---|
Related Products
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateDuratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateThis aluminium blanking plate replaces the standard exhaust gas recirculation (EGR) valve on all Duratec engines. It improves engine power and assists engine tuning by allowing the engine to use fresh oxygen for the combustion process instead of using recirculated exhaust gas. Simply remove the existing exhaust gas recirculation valve and replace with the blanking plate using silicon gasket sealant. Image shows blanking plate on right and original exhaust gas recirculation valve on left.
Duratec Water Manifold
Duratec Water ManifoldDesigned to simplify the cooling system when used in a longitudinal engine position. The depth from the rear cylinder head face is 60mm. Incorporates heater outlet. Comes with temperature gauge sender.
£231.53Add to basket
Products that you might find interesting
Slave Cylinder for Toyota W Series Hydraulic Release Bearing Kit
Slave Cylinder for Toyota W Series Hydraulic Release Bearing Kit£115.00Add to basket
Slave Cylinder for Toyota W Series Hydraulic Release Bearing Kit
Slave Cylinder for Toyota W Series Hydraulic Release Bearing KitThis slave cylinder is a replacement for the Toyota W Series Hydraulic Release Bearing Kit.
For use with a 0.625 inch (5/8″) master cylinder.
£115.00Add to basket
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch£115.00Select options
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic ClutchThis slave cylinder fits directly inside our Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing. For use with a 0.625 inch (5/8″) master cylinder.
£115.00Select options
Duratec Water Manifold
Duratec Water ManifoldDesigned to simplify the cooling system when used in a longitudinal engine position. The depth from the rear cylinder head face is 60mm. Incorporates heater outlet. Comes with temperature gauge sender.
£231.53Add to basket
Honda K20 or K24 Water Outlet
Honda K20 or K24 Water OutletHonda K20 upper coolant housing that redirects the outlet to 90 degrees from the engine.
Honda K20 Lightweight Steel Flywheel – Standard Clutch Plate
Honda K20 Lightweight Steel Flywheel – Standard Clutch Plate£318.32Add to basket
Honda K20 Lightweight Steel Flywheel – Standard Clutch Plate
Honda K20 Lightweight Steel Flywheel – Standard Clutch PlateHonda K20 lightweight steel flywheel to suit standard clutch cover and plate. With integral starter ring (ring gear is machined into the flywheel)
£318.32Add to basket
Duratec Exhaust Manifold
Duratec Exhaust ManifoldThis is a Tony Law exhaust manifold that will fit the 2.0 and 2.3 litre Duratec engines. Please specify your engine size below. This will give you a custom exhaust manifold with downpipe lengths matched to the engine’s power characteristics. The manifold will also be matched to your engine’s deck height, dependent on engine size. The 3 piece manifold offers good resistance to fracturing in high stress competition situations as the attachment point to the bellhousing is where the Y piece below attaches to the 2 manifold upper pieces. As these manifolds are custom made the lead time can be up to 14 days depending on engine size and availability.
£625.00Select options