2000e Clutch Release Bearing
2000e Clutch Release Bearing
£30.50
2000e clutch release bearing. Smaller internal diameter to suit the 7/8″ input shaft sleeve.
Related Products
2000E Gearbox with Cable Clutch Bellhousing
2000E Gearbox with Cable Clutch Bellhousing£168.00Add to basket
2000E Gearbox with Cable Clutch Bellhousing
2000E Gearbox with Cable Clutch BellhousingFor use with the 2000E 3 rail gearbox when utilising a cable clutch.
£168.00Add to basket
Products that you might find interesting
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Borg Warner T5 Hydraulic Release Bearing Kit
Borg Warner T5 Hydraulic Release Bearing Kit£152.25Select options
Borg Warner T5 Hydraulic Release Bearing Kit
Borg Warner T5 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing T5 gearbox. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
£152.25Select options
Zetec RWD Starter Motor
Zetec RWD Starter MotorThis starter motor can be used in conjunction with the RS2000 Type Bellhousing (cable clutch), the Sierra Direct Replacement Cable Clutch Bellhousing and Sierra Direct Replacement Hydraulic Clutch Bellhousing bellhousings. Equivalent to LRS707.
NOTE
This starter motor has 10mm less pinion offset to accommodate a standard Zetec E fitted to a Ford Type 9 or Borg Warner T5. Please note that some aftermarket lightweight flywheels are manufactured with a different offset to allow the fitment of standard Pinto or X-flow starter motors. Please check that your flywheel is the standard Zetec E item.
£105.00Add to basket
Toyota W series Hydraulic Release Bearing Kit Without Slave Cylinder
Toyota W series Hydraulic Release Bearing Kit Without Slave CylinderToyota W series Hydraulic Release Bearing Kit Without Slave Cylinder
Toyota W series Hydraulic Release Bearing Kit Without Slave CylinderThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing Toyota W series gearbox minus the slave cylinder found in the Toyota W Series Hydraulic Release Bearing Kit.
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release BearingPlumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release BearingConnects our Toyota W Series Hydraulic Release Bearing Kit to your car’s pedal box or engine bay mounted master cylinder.
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox£47.25 – £57.25Select options
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford GearboxAdapter plate which fits between any of our Ford gearbox bellhousings and a Type 9 (Sierra) 2.8 gearbox. The 2.8 gearbox uses a longer 1st motion shaft hence the need for an adaptor plate.
£47.25 – £57.25Select options