Vauxhall XE ARP Flywheel Bolt Set
Vauxhall XE ARP Flywheel Bolt Set
£47.70
For all petrol Duratec engines 1.8 litre, 2.0 litre and 2.3 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Suitable for the following flywheels:
Vauxhall 2.0XE Lightweight Steel Flywheel Ford Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Standard Cover
Additional information
| Weight | 0.2 kg |
|---|
Related Products
Vauxhall 2.0XE Lightweight Steel Flywheel Ford Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Ford Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Ford Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Ford CoverVauxhall 2.0XE (red top) lightweight steel flywheel to suit Ford 8 1/2″ friction clutch plate and Ford Pinto Vauxhall cover.
Machined from billet steel, our flywheels feature an integral ring gear. Much lighter than the original flywheel this flywheel is suitable for a standard or uprated Ford 8 1/2″ clutch plate Ford Pinto cover, allowing the engine to mate to 23 spline 1″ Type 9 or Rocket Ford gearboxes.
Vauxhall 2.0XE Lightweight Steel Flywheel Standard Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Standard Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Standard Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Standard CoverVauxhall 2.0XE (red top) lightweight steel flywheel to suit Ford 8 1/2″ friction clutch plate and standard Vauxhall cover. Machined from billet steel, our flywheels feature an integral ring gear. Much lighter than the original flywheel this flywheel is suitable for a standard or uprated Ford 8 1/2″ clutch plate and the standard Vauxhall cover, allowing the engine to mate to 23 spline 1″ Type 9 or Rocket Ford gearboxes.
Products that you might find interesting
Fine Cap Head Bolts (4)
Fine Cap Head Bolts (4)4 12mm x 1 1/2mm pitch x 40mm long fine cap head bolts for when a standard fitment bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox internally.
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, replacing the standard gearbox nose. The kit comes completed with replacement seal and fixings. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic ClutchThis slave cylinder fits directly inside our Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing. For use with a 0.625 inch (5/8″) master cylinder.
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic ClutchAdapter plate which fits between the Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing and a Type E (Rocket) or Type 9 (Sierra) gearbox.
You will also need our Slave Cylinder for this conversion
