Toyota 1KR-FE Engine to Toyota W56 Gearbox Spigot Bearing
Toyota 1KR-FE Engine to Toyota W56 Gearbox Spigot Bearing
£13.00
Converts the 1KR-FE engine crankshaft to accommodate the Toyota W range of gearboxes in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
Consists of 1 roller bearing race. Allows a Toyota 1KR-FE engine to be connected to the Toyota W range of gearboxes using our Toyota 1KR-FE Engine to Toyota W Series Gearbox Bellhousing.
Additional information
Weight | 0.1 kg |
---|
Related Products
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and Cover
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and Cover£162.00Add to basket
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and Cover
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and CoverConnects the Toyota 1KR-FE engine to the range of Toyota W Series gearboxes
£162.00Add to basket
1KR-FE Toyota Engine to Toyota W Series Gearbox Bellhousing
1KR-FE Toyota Engine to Toyota W Series Gearbox Bellhousing£231.00Add to basket
1KR-FE Toyota Engine to Toyota W Series Gearbox Bellhousing
1KR-FE Toyota Engine to Toyota W Series Gearbox BellhousingAllows the 1.0 litre Toyota 1KR-FE engine to be mated to the range of Toyota W series 5 speed gearboxes available in a longitudinal installation.
£231.00Add to basket
Products that you might find interesting
10mm Cap Head Bolts (4)
10mm Cap Head Bolts (4)4 10mm x 1 1/2mm pitch cap head bolts for when a quick release bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox externally straight through the original tapped 12mm holes of the Ford gearbox and screwed into the 10mm tapped holes of the quick release bellhousing.
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic ClutchAdapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic ClutchAdapter plate which fits between the Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing and a Type E (Rocket) or Type 9 (Sierra) gearbox.
You will also need our Slave Cylinder for this conversion
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing Kit£170.00Select options
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, replacing the standard gearbox nose. The kit comes completed with replacement seal and fixings. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
£170.00Select options
Fine Cap Head Bolts (4)
Fine Cap Head Bolts (4)4 12mm x 1 1/2mm pitch x 40mm long fine cap head bolts for when a standard fitment bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox internally.
Duratec ARP flywheel bolt set
Duratec ARP flywheel bolt setFor all petrol Duratec engines 1.8 litre, 2.0 litre and 2.3 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Plumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release BearingPlumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release BearingConnects our Ford Type 9 Hydraulic Release Bearing Kit or Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch to your car’s pedal box. Comes with fittings and enough pipe to allow the bleed nipple to be situated remotely.