Zetec SE ARP flywheel bolt set
Zetec SE ARP flywheel bolt set
£47.70
For all Zetec SE engines 1.4, 1.6 and 1.7 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Suitable for the following flywheel:
Ford Zetec SE Lightweight Steel Flywheel
Additional information
Weight | 0.2 kg |
---|
Related Products
Ford Zetec SE / Sigma Lightweight Steel Flywheel
Ford Zetec SE / Sigma Lightweight Steel Flywheel£312.75Add to basket
Ford Zetec SE / Sigma Lightweight Steel Flywheel
Ford Zetec SE / Sigma Lightweight Steel FlywheelFord Ford Zetec SE (Sigma)* lightweight steel flywheel to suit standard diameter Zetec SE clutch cover. Designed to replace the OE flywheel. Machined from billet steel, our flywheels feature an integral ring gear. Much lighter than the original flywheel.
£312.75Add to basket
Zetec SE to Ford Gearbox Bellhousing
Zetec SE to Ford Gearbox Bellhousing£189.00Add to basket
Zetec SE to Ford Gearbox Bellhousing
Zetec SE to Ford Gearbox BellhousingThis bellhousing will mate the Ford Zetec SE (Sigma)* engine to the Ford Type E (Rocket) 4 speed or Ford Type 9 (Sierra) 5 speed gearbox.
£189.00Add to basket
Products that you might find interesting
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing Kit£170.00Select options
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, replacing the standard gearbox nose. The kit comes completed with replacement seal and fixings. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
£170.00Select options
Duratec ARP flywheel bolt set
Duratec ARP flywheel bolt setFor all petrol Duratec engines 1.8 litre, 2.0 litre and 2.3 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingDuratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingConverts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
Zetec RWD Starter Motor
Zetec RWD Starter MotorThis starter motor can be used in conjunction with the RS2000 Type Bellhousing (cable clutch), the Sierra Direct Replacement Cable Clutch Bellhousing and Sierra Direct Replacement Hydraulic Clutch Bellhousing bellhousings. Equivalent to LRS707.
NOTE
This starter motor has 10mm less pinion offset to accommodate a standard Zetec E fitted to a Ford Type 9 or Borg Warner T5. Please note that some aftermarket lightweight flywheels are manufactured with a different offset to allow the fitment of standard Pinto or X-flow starter motors. Please check that your flywheel is the standard Zetec E item.
£105.00Add to basket