Zetec SE ARP flywheel bolt set
Zetec SE ARP flywheel bolt set
£47.70
For all Zetec SE engines 1.4, 1.6 and 1.7 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Suitable for the following flywheel:
Ford Zetec SE Lightweight Steel Flywheel
Additional information
Weight | 0.2 kg |
---|
Related Products
Ford Zetec SE / Sigma Lightweight Steel Flywheel
Ford Zetec SE / Sigma Lightweight Steel Flywheel£312.75Add to basket
Ford Zetec SE / Sigma Lightweight Steel Flywheel
Ford Zetec SE / Sigma Lightweight Steel FlywheelFord Ford Zetec SE (Sigma)* lightweight steel flywheel to suit standard diameter Zetec SE clutch cover. Designed to replace the OE flywheel. Machined from billet steel, our flywheels feature an integral ring gear. Much lighter than the original flywheel.
£312.75Add to basket
Zetec SE to Ford Gearbox Bellhousing
Zetec SE to Ford Gearbox Bellhousing£189.00Add to basket
Zetec SE to Ford Gearbox Bellhousing
Zetec SE to Ford Gearbox BellhousingThis bellhousing will mate the Ford Zetec SE (Sigma)* engine to the Ford Type E (Rocket) 4 speed or Ford Type 9 (Sierra) 5 speed gearbox.
£189.00Add to basket
Products that you might find interesting
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Plumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release BearingPlumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release BearingConnects our Ford Type 9 Hydraulic Release Bearing Kit or Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch to your car’s pedal box. Comes with fittings and enough pipe to allow the bleed nipple to be situated remotely.
Fine Cap Head Bolts (4)
Fine Cap Head Bolts (4)4 12mm x 1 1/2mm pitch x 40mm long fine cap head bolts for when a standard fitment bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox internally.
2000e Clutch Release Bearing
2000e Clutch Release Bearing2000e clutch release bearing. Smaller internal diameter to suit the 7/8″ input shaft sleeve.
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Zetec RWD Starter Motor
Zetec RWD Starter MotorThis starter motor can be used in conjunction with the RS2000 Type Bellhousing (cable clutch), the Sierra Direct Replacement Cable Clutch Bellhousing and Sierra Direct Replacement Hydraulic Clutch Bellhousing bellhousings. Equivalent to LRS707.
NOTE
This starter motor has 10mm less pinion offset to accommodate a standard Zetec E fitted to a Ford Type 9 or Borg Warner T5. Please note that some aftermarket lightweight flywheels are manufactured with a different offset to allow the fitment of standard Pinto or X-flow starter motors. Please check that your flywheel is the standard Zetec E item.
£105.00Add to basket