Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
£33.60
Adapter plate which fits between the Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing and a Type E (Rocket) or Type 9 (Sierra) gearbox.
You will also need our Slave Cylinder for this conversion
Great part fits like a glove
IF you are going to fit any other clutch than stock, measure before the difference between the stock clutch height.
I'm going to be using a Retroford billet heavyduty clutch kit and it requiered 8mm to be taken off the thickness of this piece.
Related Products
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch£115.00Select options
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic ClutchThis slave cylinder fits directly inside our Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing. For use with a 0.625 inch (5/8″) master cylinder.
£115.00Select options
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing£260.00Select options
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch BellhousingThis bellhousing allows the 1.8l, 2.0l or 2.3l Duratec engine to be connected to the Ford Type E (Rocket 4 sp) and Type 9 (Sierra 5 sp) gearboxes using a hydraulic clutch.
£260.00Select options
Products that you might find interesting
10mm Cap Head Bolts (4)
10mm Cap Head Bolts (4)4 10mm x 1 1/2mm pitch cap head bolts for when a quick release bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox externally straight through the original tapped 12mm holes of the Ford gearbox and screwed into the 10mm tapped holes of the quick release bellhousing.
2000e Clutch Release Bearing
2000e Clutch Release Bearing2000e clutch release bearing. Smaller internal diameter to suit the 7/8″ input shaft sleeve.
Duratec ARP flywheel bolt set
Duratec ARP flywheel bolt setFor all petrol Duratec engines 1.8 litre, 2.0 litre and 2.3 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox£47.25 – £57.25Select options
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford GearboxAdapter plate which fits between any of our Ford gearbox bellhousings and a Type 9 (Sierra) 2.8 gearbox. The 2.8 gearbox uses a longer 1st motion shaft hence the need for an adaptor plate.
£47.25 – £57.25Select options
Spigot bearing
Spigot bearingConverts crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Borg Warner T5* input shaft. Fits in standard recess in crankshaft.
* With 15mm spigot
Zetec RWD Starter Motor
Zetec RWD Starter MotorThis starter motor can be used in conjunction with the RS2000 Type Bellhousing (cable clutch), the Sierra Direct Replacement Cable Clutch Bellhousing and Sierra Direct Replacement Hydraulic Clutch Bellhousing bellhousings. Equivalent to LRS707.
NOTE
This starter motor has 10mm less pinion offset to accommodate a standard Zetec E fitted to a Ford Type 9 or Borg Warner T5. Please note that some aftermarket lightweight flywheels are manufactured with a different offset to allow the fitment of standard Pinto or X-flow starter motors. Please check that your flywheel is the standard Zetec E item.
£105.00Add to basket