Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
£33.60
Adapter plate which fits between the Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing and a Type E (Rocket) or Type 9 (Sierra) gearbox.
You will also need our Slave Cylinder for this conversion
Great part fits like a glove
IF you are going to fit any other clutch than stock, measure before the difference between the stock clutch height.
I'm going to be using a Retroford billet heavyduty clutch kit and it requiered 8mm to be taken off the thickness of this piece.
Related Products
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch£115.00Select options
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic ClutchThis slave cylinder fits directly inside our Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing. For use with a 0.625 inch (5/8″) master cylinder.
£115.00Select options
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing£260.00Select options
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch BellhousingThis bellhousing allows the 1.8l, 2.0l or 2.3l Duratec engine to be connected to the Ford Type E (Rocket 4 sp) and Type 9 (Sierra 5 sp) gearboxes using a hydraulic clutch.
£260.00Select options
Products that you might find interesting
Longer Fine Cap Head Bolts for 2.8 Gearbox (4)
Longer Fine Cap Head Bolts for 2.8 Gearbox (4)For use with the Adaptor Plate for RS2000 Type Bellhousing to 2.8 Gearbox.
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Zetec SE ARP flywheel bolt set
Zetec SE ARP flywheel bolt setFor all Zetec SE engines 1.4, 1.6 and 1.7 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Spigot bearing
Spigot bearingConverts crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Borg Warner T5* input shaft. Fits in standard recess in crankshaft.
* With 15mm spigot
Longer 10mm Cap Head Bolts (4)
Longer 10mm Cap Head Bolts (4)4 10mm x 1 1/2mm pitch longer cap head bolts for when a quick release bellhousing together with the 20mm adapter plate is specified. These bolts allow the bellhousing to be attached to the Ford gearbox externally straight through the original tapped 12mm holes of the Ford gearbox, through the adapter plate and screwed into the 10mm tapped holes of the quick release bellhousing.
Toyota W Series Hydraulic Release Bearing Kit
Toyota W Series Hydraulic Release Bearing Kit£152.25Add to basket
Toyota W Series Hydraulic Release Bearing Kit
Toyota W Series Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing Toyota W series gearbox.
£152.25Add to basket