Duratec Water Manifold
Duratec Water Manifold
£231.53
Designed to simplify the cooling system when used in a longitudinal engine position. The depth from the rear cylinder head face is 60mm. Incorporates heater outlet. Comes with temperature gauge sender.
Specification and Application
| Component | Duratec Water Manifold |
| Type | Cast aluminium pipes and components |
| Engines | Ford 1.8 Duratec Ford 2.0 Duratec Ford 2.3 Duratec Ford 2.5 Duratec |
| Applications | Kit Cars Rally/Race – MkI/II Escort, Sierra, Lotus Cortina BriSCA F2 Classic Ford |
Additional information
| Weight | 4 kg |
|---|
Related Products
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateThis aluminium blanking plate replaces the standard exhaust gas recirculation (EGR) valve on all Duratec engines. It improves engine power and assists engine tuning by allowing the engine to use fresh oxygen for the combustion process instead of using recirculated exhaust gas. Simply remove the existing exhaust gas recirculation valve and replace with the blanking plate using silicon gasket sealant. Image shows blanking plate on right and original exhaust gas recirculation valve on left.
Duratec Thermostat and Housing
Duratec Thermostat and HousingMechanically controlled and replaces standard Mondeo Duratec item that is controlled by the Mondeo ECU.
Products that you might find interesting
Billet Aluminium Hydraulic Heavy Duty Release Bearing Seal Kit
Billet Aluminium Hydraulic Heavy Duty Release Bearing Seal Kit
Billet Aluminium Hydraulic Heavy Duty Release Bearing Seal Kit
Billet Aluminium Hydraulic Heavy Duty Release Bearing Seal KitReplacement seal kit containing 3 seals and the correct seal grease.
Westfield Duratec Engine Mounting Kit
Westfield Duratec Engine Mounting KitA complete Westfield Engine Mounting Kit
Zetec RWD Starter Motor
Zetec RWD Starter MotorThis starter motor can be used in conjunction with the RS2000 Type Bellhousing (cable clutch), the Sierra Direct Replacement Cable Clutch Bellhousing and Sierra Direct Replacement Hydraulic Clutch Bellhousing bellhousings. Equivalent to LRS707.
NOTE
This starter motor has 10mm less pinion offset to accommodate a standard Zetec E fitted to a Ford Type 9 or Borg Warner T5. Please note that some aftermarket lightweight flywheels are manufactured with a different offset to allow the fitment of standard Pinto or X-flow starter motors. Please check that your flywheel is the standard Zetec E item.
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
Slave Cylinder for Toyota W Series Hydraulic Release Bearing Kit
Slave Cylinder for Toyota W Series Hydraulic Release Bearing Kit
Slave Cylinder for Toyota W Series Hydraulic Release Bearing Kit
Slave Cylinder for Toyota W Series Hydraulic Release Bearing KitThis slave cylinder is a replacement for the Toyota W Series Hydraulic Release Bearing Kit.
For use with a 0.625 inch (5/8″) master cylinder.
16 Valve Astra Inlet Manifold
16 Valve Astra Inlet ManifoldTo convert 16 Valve Astra 2.0XE engine to twin Weber 40 or 45 carburettors. Studs & nuts included. Cosworth type mount ‘o’ ring plates not included.
* Please note that the manifold is only compatible with 0 degrees mounted engines, not 7 degree standard angle.
