Zetec SE ARP flywheel bolt set
Zetec SE ARP flywheel bolt set
£47.70
For all Zetec SE engines 1.4, 1.6 and 1.7 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Suitable for the following flywheel:
Ford Zetec SE Lightweight Steel Flywheel
Additional information
| Weight | 0.2 kg |
|---|
Related Products
Ford Zetec SE / Sigma Lightweight Steel Flywheel
Ford Zetec SE / Sigma Lightweight Steel Flywheel
Ford Zetec SE / Sigma Lightweight Steel Flywheel
Ford Zetec SE / Sigma Lightweight Steel FlywheelFord Ford Zetec SE (Sigma)* lightweight steel flywheel to suit standard diameter Zetec SE clutch cover. Designed to replace the OE flywheel. Machined from billet steel, our flywheels feature an integral ring gear. Much lighter than the original flywheel.
Zetec SE to Ford Gearbox Bellhousing
Zetec SE to Ford Gearbox BellhousingThis bellhousing will mate the Ford Zetec SE (Sigma)* engine to the Ford Type E (Rocket) 4 speed or Ford Type 9 (Sierra) 5 speed gearbox.
Products that you might find interesting
Longer Fine Cap Head Bolts for 2.8 Gearbox (4)
Longer Fine Cap Head Bolts for 2.8 Gearbox (4)For use with the Adaptor Plate for RS2000 Type Bellhousing to 2.8 Gearbox.
10mm Cap Head Bolts (4)
10mm Cap Head Bolts (4)4 10mm x 1 1/2mm pitch cap head bolts for when a quick release bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox externally straight through the original tapped 12mm holes of the Ford gearbox and screwed into the 10mm tapped holes of the quick release bellhousing.
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford GearboxAdapter plate which fits between any of our Ford gearbox bellhousings and a Type 9 (Sierra) 2.8 gearbox. The 2.8 gearbox uses a longer 1st motion shaft hence the need for an adaptor plate.
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 GearboxThis slave cylinder fits directly inside our VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing or VW / Audi 1.8 Litre to Ford Type 9 Bellhousing.
For use with a 0.625 inch (5/8″) master cylinder.
RS2000 Replacement Competition Heavy Duty Release Bearing
RS2000 Replacement Competition Heavy Duty Release Bearing
RS2000 Replacement Competition Heavy Duty Release Bearing
RS2000 Replacement Competition Heavy Duty Release BearingFor use in any application where a Ford RS2000 pattern release bearing is currently used and where the requirement is for a heavy duty all steel sealed ball bearing.
