2000e Clutch Release Bearing
2000e Clutch Release Bearing
£30.50
2000e clutch release bearing. Smaller internal diameter to suit the 7/8″ input shaft sleeve.
Related Products
2000E Gearbox with Cable Clutch Bellhousing
2000E Gearbox with Cable Clutch Bellhousing£168.00Add to basket
2000E Gearbox with Cable Clutch Bellhousing
2000E Gearbox with Cable Clutch BellhousingFor use with the 2000E 3 rail gearbox when utilising a cable clutch.
£168.00Add to basket
Products that you might find interesting
Zetec RWD Starter Motor
Zetec RWD Starter MotorThis starter motor can be used in conjunction with the RS2000 Type Bellhousing (cable clutch), the Sierra Direct Replacement Cable Clutch Bellhousing and Sierra Direct Replacement Hydraulic Clutch Bellhousing bellhousings. Equivalent to LRS707.
NOTE
This starter motor has 10mm less pinion offset to accommodate a standard Zetec E fitted to a Ford Type 9 or Borg Warner T5. Please note that some aftermarket lightweight flywheels are manufactured with a different offset to allow the fitment of standard Pinto or X-flow starter motors. Please check that your flywheel is the standard Zetec E item.
£105.00Add to basket
Borg Warner T5 Hydraulic Heavy Duty Release Bearing Kit
Borg Warner T5 Hydraulic Heavy Duty Release Bearing Kit£230.00Select options
Borg Warner T5 Hydraulic Heavy Duty Release Bearing Kit
Borg Warner T5 Hydraulic Heavy Duty Release Bearing KitThis kit utilises a concentric heavy duty release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing T5 gearbox. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
£230.00Select options
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch£115.00Select options
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic ClutchThis slave cylinder fits directly inside our Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing. For use with a 0.625 inch (5/8″) master cylinder.
£115.00Select options
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic ClutchAdapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic ClutchAdapter plate which fits between the Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing and a Type E (Rocket) or Type 9 (Sierra) gearbox.
You will also need our Slave Cylinder for this conversion
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox£47.25 – £57.25Select options
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford GearboxAdapter plate which fits between any of our Ford gearbox bellhousings and a Type 9 (Sierra) 2.8 gearbox. The 2.8 gearbox uses a longer 1st motion shaft hence the need for an adaptor plate.
£47.25 – £57.25Select options