Billet Aluminium Hydraulic Heavy Duty Release Bearing Mounting Kit
Billet Aluminium Hydraulic Heavy Duty Release Bearing Mounting Kit
£78.00
High quality heavy duty release bearing mounting kit.
Silver anodised mounting boss to be used with our heavy duty release bearing. This can be specified for either a Type 9 5 speed gearbox with gasket or Type “E” 4 speed gearbox with an ‘o’ ring seal.
The mounting boss replaces the standard gearbox nose.
If greater reach is needed please purchase the Anodised Silver Spacer for Billet Aluminium Hydraulic Heavy Duty Release Bearing. This can be machined to the correct thickness.
Specification and Application
| Component | Hydraulic Heavy Duty Release Bearing |
| Includes | Silver anodised mounting boss, seal, gasket or o ring, bolts and washers |
| Applications | MkI/II Escort Westfield Caterham Kit Car |
* When using a shallower clutch cover the release bearing may need spacing forward in order to achieve full clutch depression
Additional information
| Weight | 1 kg |
|---|---|
| Mounting Boss | Type 9, Type E |
Related Products
Anodised Silver Spacer for Billet Aluminium Hydraulic Heavy Duty Release Bearing
Anodised Silver Spacer for Billet Aluminium Hydraulic Heavy Duty Release Bearing
Anodised Silver Spacer for Billet Aluminium Hydraulic Heavy Duty Release Bearing
Anodised Silver Spacer for Billet Aluminium Hydraulic Heavy Duty Release Bearing12mm anodised silver adapter plate which fits between the Billet Aluminium Hydraulic Heavy Duty Release Bearing and its mounting boss.
Billet Aluminium Hydraulic Heavy Duty Release Bearing
Billet Aluminium Hydraulic Heavy Duty Release Bearing
Billet Aluminium Hydraulic Heavy Duty Release Bearing
Billet Aluminium Hydraulic Heavy Duty Release BearingHigh quality rebuildable heavy duty release bearing.
Products that you might find interesting
2000e Clutch Release Bearing
2000e Clutch Release Bearing2000e clutch release bearing. Smaller internal diameter to suit the 7/8″ input shaft sleeve.
Longer 10mm Cap Head Bolts (4)
Longer 10mm Cap Head Bolts (4)4 10mm x 1 1/2mm pitch longer cap head bolts for when a quick release bellhousing together with the 20mm adapter plate is specified. These bolts allow the bellhousing to be attached to the Ford gearbox externally straight through the original tapped 12mm holes of the Ford gearbox, through the adapter plate and screwed into the 10mm tapped holes of the quick release bellhousing.
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Duratec ARP flywheel bolt set
Duratec ARP flywheel bolt setFor all petrol Duratec engines 1.8 litre, 2.0 litre and 2.3 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford GearboxAdapter plate which fits between any of our Ford gearbox bellhousings and a Type 9 (Sierra) 2.8 gearbox. The 2.8 gearbox uses a longer 1st motion shaft hence the need for an adaptor plate.
Spigot bearing 10mm internal diameter
Spigot bearing 10mm internal diameterConverts the Zetec SE / Sigma 1.7 VCT crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Rocket input shaft. Fits in standard recess in crankshaft.
