Duratec ARP flywheel bolt set
Duratec ARP flywheel bolt set
£47.70
For all petrol Duratec engines 1.8 litre, 2.0 litre and 2.3 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Suitable for the following flywheels:
Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Additional information
Weight | 0.2 kg |
---|
Arrived on time and as ordered, good service.
Related Products
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate£303.85Add to basket
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate2.0 or 2.3 Ford Duratec lightweight steel flywheel to suit Twin plate 7 1/4″ paddle clutch. With integral starter ring (ring gear is machined into the flywheel)
£303.85Add to basket
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate£250.00Add to basket
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
£250.00Add to basket
Products that you might find interesting
2000e Clutch Release Bearing
2000e Clutch Release Bearing2000e clutch release bearing. Smaller internal diameter to suit the 7/8″ input shaft sleeve.
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Zetec RWD Starter Motor
Zetec RWD Starter MotorThis starter motor can be used in conjunction with the RS2000 Type Bellhousing (cable clutch), the Sierra Direct Replacement Cable Clutch Bellhousing and Sierra Direct Replacement Hydraulic Clutch Bellhousing bellhousings. Equivalent to LRS707.
NOTE
This starter motor has 10mm less pinion offset to accommodate a standard Zetec E fitted to a Ford Type 9 or Borg Warner T5. Please note that some aftermarket lightweight flywheels are manufactured with a different offset to allow the fitment of standard Pinto or X-flow starter motors. Please check that your flywheel is the standard Zetec E item.
£105.00Add to basket
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingDuratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingConverts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.