Vauxhall XE ARP Flywheel Bolt Set
Vauxhall XE ARP Flywheel Bolt Set
£47.70
For all petrol Duratec engines 1.8 litre, 2.0 litre and 2.3 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Suitable for the following flywheels:
Vauxhall 2.0XE Lightweight Steel Flywheel Ford Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Standard Cover
Additional information
| Weight | 0.2 kg |
|---|
Related Products
Vauxhall 2.0XE Lightweight Steel Flywheel Ford Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Ford Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Ford Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Ford CoverVauxhall 2.0XE (red top) lightweight steel flywheel to suit Ford 8 1/2″ friction clutch plate and Ford Pinto Vauxhall cover.
Machined from billet steel, our flywheels feature an integral ring gear. Much lighter than the original flywheel this flywheel is suitable for a standard or uprated Ford 8 1/2″ clutch plate Ford Pinto cover, allowing the engine to mate to 23 spline 1″ Type 9 or Rocket Ford gearboxes.
Vauxhall 2.0XE Lightweight Steel Flywheel Standard Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Standard Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Standard Cover
Vauxhall 2.0XE Lightweight Steel Flywheel Standard CoverVauxhall 2.0XE (red top) lightweight steel flywheel to suit Ford 8 1/2″ friction clutch plate and standard Vauxhall cover. Machined from billet steel, our flywheels feature an integral ring gear. Much lighter than the original flywheel this flywheel is suitable for a standard or uprated Ford 8 1/2″ clutch plate and the standard Vauxhall cover, allowing the engine to mate to 23 spline 1″ Type 9 or Rocket Ford gearboxes.
Products that you might find interesting
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 GearboxThis slave cylinder fits directly inside our VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing or VW / Audi 1.8 Litre to Ford Type 9 Bellhousing.
For use with a 0.625 inch (5/8″) master cylinder.
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford GearboxAdapter plate which fits between any of our Ford gearbox bellhousings and a Type 9 (Sierra) 2.8 gearbox. The 2.8 gearbox uses a longer 1st motion shaft hence the need for an adaptor plate.
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingConverts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
Spigot bearing
Spigot bearingConverts crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Borg Warner T5* input shaft. Fits in standard recess in crankshaft.
* With 15mm spigot
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Borg Warner T5 Hydraulic Release Bearing Kit
Borg Warner T5 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing T5 gearbox. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
