Duratec Engine to Toyota W Series Gearbox Bellhousing
Duratec Engine to Toyota W Series Gearbox Bellhousing
£264.60
Allows the Ford Duratec engine to be mated to the wide range of Toyota W series 5 speed gearboxes available. These gearboxes, in particular the DW56 are a strong and slick shifting alternative to the Sierra 5 speed boxes, which are increasingly in short supply.
If you are struggling to locate a Ford Type 9 gearbox then the Toyota W series gearboxes are a suitable replacement for rear wheel drive installations. Our bellhousing connects the Ford Duratec 4 cylinder engine to any of the range of gearboxes displayed below.
Specification and Application
| Component | Ford Duratec to Toyota W series |
| Type | Bare casting Machined on front and rear faces |
| Actuation | Hydraulic slave cylinder |
| Gearbox to Engine Face | 6.496 inch (165mm) |
| Engines | Ford 1.8 Duratec Ford 2.0 Duratec Ford 2.3 Duratec Ford 2.5 Duratec |
| Gearbox | Toyota W series including: W56 W58 |
| Applications | Kit cars Rally / race |
Additional information
| Weight | 5.5 kg |
|---|
Related Products
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingConverts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release BearingConnects our Toyota W Series Hydraulic Release Bearing Kit to your car’s pedal box or engine bay mounted master cylinder.
Toyota W Series Hydraulic Release Bearing Kit
Toyota W Series Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing Toyota W series gearbox.
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
Products that you might find interesting
Sierra Direct Replacement Cable Clutch Bellhousing
Sierra Direct Replacement Cable Clutch Bellhousing
Sierra Direct Replacement Cable Clutch Bellhousing
Sierra Direct Replacement Cable Clutch BellhousingThis bellhousing is a direct replacement for the cast iron Ford Sierra item.
Ford Coyote V8 Engine to Quaife Bellhousing
Ford Coyote V8 Engine to Quaife BellhousingConnects the Ford Coyote V8 Engine to the Quaife 69G heavy duty 6 speed sequential gearbox.
2000E Gearbox with Cable Clutch Bellhousing
2000E Gearbox with Cable Clutch BellhousingFor use with the 2000E 3 rail gearbox when utilising a cable clutch.
Millington Diamond Engine to Ford Gearbox
Millington Diamond Engine to Ford GearboxMillington Diamond engine to ford gearbox without starter motor boss.
Zetec SE to Ford Gearbox Bellhousing
Zetec SE to Ford Gearbox BellhousingThis bellhousing will mate the Ford Zetec SE (Sigma)* engine to the Ford Type E (Rocket) 4 speed or Ford Type 9 (Sierra) 5 speed gearbox.
VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing
VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing
VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing
VW / Audi 1.8 Litre to Borg Warner T5 BellhousingThis bellhousing will mate the Volkswagen, Audi, SEAT or Skoda 1.8 litre 20 valve turbocharged engines to the Borg Warner T5 (2WD Cosworth) gearbox.
