Fine Cap Head Bolts (4)
Fine Cap Head Bolts (4)
£7.00
4 12mm x 1 1/2mm pitch x 40mm long fine cap head bolts for when a standard fitment bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox internally.
Quick fit bellhousing fitments use standard 10mm cap head bolts attached to the bellhousing externally.
Additional information
| Weight | 0.25 kg |
|---|
Related Products
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch BellhousingThis bellhousing allows the 1.8l, 2.0l or 2.3l Duratec engine to be connected to the Ford Type E (Rocket 4 sp) and Type 9 (Sierra 5 sp) gearboxes using a hydraulic clutch.
Duratec Engine to Ford Gearbox Cable Clutch Bellhousing
Duratec Engine to Ford Gearbox Cable Clutch Bellhousing
Duratec Engine to Ford Gearbox Cable Clutch Bellhousing
Duratec Engine to Ford Gearbox Cable Clutch BellhousingThis bellhousing allows the 1.8l, 2.0l or 2.3l Duratec engine to be connected to the Ford Type E (Rocket 4 sp) and Type 9 (Sierra 5 sp) gearboxes using a cable clutch.
Zetec SE to Ford Gearbox Bellhousing
Zetec SE to Ford Gearbox BellhousingThis bellhousing will mate the Ford Zetec SE (Sigma)* engine to the Ford Type E (Rocket) 4 speed or Ford Type 9 (Sierra) 5 speed gearbox.
Vauxhall 2.0XE Engine to Ford Gearbox Cable Clutch Bellhousing
Vauxhall 2.0XE Engine to Ford Gearbox Cable Clutch Bellhousing
Vauxhall 2.0XE Engine to Ford Gearbox Cable Clutch Bellhousing
Vauxhall 2.0XE Engine to Ford Gearbox Cable Clutch BellhousingThis bellhousing allows the Vauxhall 2.0XE Engine to be connected to the Ford Type E (Rocket 4 sp) and Type 9 (Sierra 5 sp) gearboxes using a cable clutch.
Products that you might find interesting
2000e Clutch Release Bearing
2000e Clutch Release Bearing2000e clutch release bearing. Smaller internal diameter to suit the 7/8″ input shaft sleeve.
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic ClutchThis slave cylinder fits directly inside our Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing. For use with a 0.625 inch (5/8″) master cylinder.
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingConverts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Spigot bearing 10mm internal diameter
Spigot bearing 10mm internal diameterConverts the Zetec SE / Sigma 1.7 VCT crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Rocket input shaft. Fits in standard recess in crankshaft.
Duratec ARP flywheel bolt set
Duratec ARP flywheel bolt setFor all petrol Duratec engines 1.8 litre, 2.0 litre and 2.3 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
