Duratec Underdrive Pulley 146mm Trigger Wheel
Duratec Underdrive Pulley 146mm Trigger Wheel
£164.30
Replaces the standard crank pulley on 2.0 and 2.3 litre Duratec engines for higher revving competition engines. Save valuable horsepower by avoiding over-spinning belt driven ancillaries.
- Machined from anodised billet steel
- Complete with integral crank position sensor 36-1 146mm trigger wheel
- 6 groove belt
- Suitable for 2.0 litre and 2.3 litre Duratec engines
- 3mm keyway
- Smaller diameter to prevent over-revving belt driven ancillaries and to save horsepower
NB: improper installation will cause valve train and / or piston damage
* The finish may be gold or matt
Additional information
| Weight | 0.5 kg |
|---|
Related Products
Duratec Universal Chassis Mounted Engine Kit
Duratec Universal Chassis Mounted Engine KitThe Duratec Universal Chassis Mounted Engine Kit allows the popular Duratec engine to be fitted in a wide range of RWD vehicles.
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateThis aluminium blanking plate replaces the standard exhaust gas recirculation (EGR) valve on all Duratec engines. It improves engine power and assists engine tuning by allowing the engine to use fresh oxygen for the combustion process instead of using recirculated exhaust gas. Simply remove the existing exhaust gas recirculation valve and replace with the blanking plate using silicon gasket sealant. Image shows blanking plate on right and original exhaust gas recirculation valve on left.
Duratec Thermostat and Housing
Duratec Thermostat and HousingMechanically controlled and replaces standard Mondeo Duratec item that is controlled by the Mondeo ECU.
Duratec Water Manifold
Duratec Water ManifoldDesigned to simplify the cooling system when used in a longitudinal engine position. The depth from the rear cylinder head face is 60mm. Incorporates heater outlet. Comes with temperature gauge sender.
Products that you might find interesting
Duratec Universal Chassis Mounted Engine Kit
Duratec Universal Chassis Mounted Engine KitThe Duratec Universal Chassis Mounted Engine Kit allows the popular Duratec engine to be fitted in a wide range of RWD vehicles.
16 Valve Astra Inlet Manifold
16 Valve Astra Inlet ManifoldTo convert 16 Valve Astra 2.0XE engine to twin Weber 40 or 45 carburettors. Studs & nuts included. Cosworth type mount ‘o’ ring plates not included.
* Please note that the manifold is only compatible with 0 degrees mounted engines, not 7 degree standard angle.
Duratec Exhaust Manifold
Duratec Exhaust ManifoldThis is a Tony Law exhaust manifold that will fit the 2.0 and 2.3 litre Duratec engines. Please specify your engine size below. This will give you a custom exhaust manifold with downpipe lengths matched to the engine’s power characteristics. The manifold will also be matched to your engine’s deck height, dependent on engine size. The 3 piece manifold offers good resistance to fracturing in high stress competition situations as the attachment point to the bellhousing is where the Y piece below attaches to the 2 manifold upper pieces. As these manifolds are custom made the lead time can be up to 14 days depending on engine size and availability.
Duratec Thermostat and Housing
Duratec Thermostat and HousingMechanically controlled and replaces standard Mondeo Duratec item that is controlled by the Mondeo ECU.
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateDuratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateThis aluminium blanking plate replaces the standard exhaust gas recirculation (EGR) valve on all Duratec engines. It improves engine power and assists engine tuning by allowing the engine to use fresh oxygen for the combustion process instead of using recirculated exhaust gas. Simply remove the existing exhaust gas recirculation valve and replace with the blanking plate using silicon gasket sealant. Image shows blanking plate on right and original exhaust gas recirculation valve on left.
Duratec Water Manifold
Duratec Water ManifoldDesigned to simplify the cooling system when used in a longitudinal engine position. The depth from the rear cylinder head face is 60mm. Incorporates heater outlet. Comes with temperature gauge sender.
Upsell Products
Duratec Underdrive Pulley 164mm Trigger Wheel
Duratec Underdrive Pulley 164mm Trigger WheelReplaces the standard crank pulley on 2.0 and 2.3 litre Duratec engines for higher revving competition engines. Save valuable horsepower by avoiding over-spinning belt driven ancillaries.
