Duratec or Ecoboost Engine to Borg Warner T5 or Tremec Gearbox Hydraulic Clutch Bellhousing
Duratec or Ecoboost Engine to Borg Warner T5 or Tremec Gearbox Hydraulic Clutch Bellhousing
£395.00
This bellhousing allows the 1.8l, 2.0l or 2.3l Duratec engine or Ford 2.0 and 2.3 Ecoboost to be connected to the a Borg Warner or Tremec T5 gearbox using a hydraulic clutch.
Connects any 4 cylinder Ford Duratec or the Ford 2.0 and 2.3 Ecoboost* engine to a Borg Warner / Tremec T5 gearbox or Sierra Cosworth T5 gearbox.
To be used with the Borg Warner T5 Hydraulic Release Bearing Kit or Borg Warner T5 Hydraulic Heavy Duty Release Bearing Kit
Not compatible with standard flywheel. Needs Ford Duratec lightweight Steel Flywheel – 8 1/2″ *** or Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate.
You may also need the spigot bearing that fits directly in the end of the crankshaft.
Please see our Ford Duratec Engine page for more information.
Please see the related products below.
Requires that the original tube where the thrust bearing slides needs cutting off leaving only the part that houses the oil seal if using our Borg Warner T5 Hydraulic Release Bearing Kit or Borg Warner T5 Hydraulic Heavy Duty Release Bearing Kit.
*Please note that Ford Ecoboost engines under 2.0 litres are the Sigma or Zetec SE bellhousing pattern.
Specification and Application
| Component | Duratec Engine to Borg Warner T5 or Tremec Hydraulic Clutch |
| Type | Bare Casting Machined on front and rear faces |
| Gearbox to Engine Face | 6.8 inch (173mm) |
| Clutch Actuation | Hydraulic |
| Engines | Ford 1.8 Duratec Ford 2.0 Duratec Ford 2.3 Duratec Ford 2.5 Duratec Ford 2.0 Ecoboost Ford 2.3 Ecoboost |
| Gearboxes | Borg Warner T5 Tremec T5 |
| Applications | Kit Cars Rally/Race – MkI/II Escort, Sierra, Lotus Cortina Classic Ford |
Additional information
| Weight | 6 kg |
|---|---|
| Gearbox Location Diameter | 123mm Borg Warner, 124.5mm Tremec or Mustang |
Related Products
Borg Warner T5 Hydraulic Heavy Duty Release Bearing Kit
Borg Warner T5 Hydraulic Heavy Duty Release Bearing Kit
Borg Warner T5 Hydraulic Heavy Duty Release Bearing Kit
Borg Warner T5 Hydraulic Heavy Duty Release Bearing KitThis kit utilises a concentric heavy duty release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing T5 gearbox. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
Borg Warner T5 Hydraulic Release Bearing Kit
Borg Warner T5 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing T5 gearbox. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
Plumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release BearingConnects our Ford Type 9 Hydraulic Release Bearing Kit or Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch to your car’s pedal box. Comes with fittings and enough pipe to allow the bleed nipple to be situated remotely.
8 1/2″ Clutch Cover and Friction Disc
8 1/2″ Clutch Cover and Friction DiscThis high quality original equipment kit includes a standard clutch cover and friction disc.
Spigot bearing
Spigot bearingConverts crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Borg Warner T5* input shaft. Fits in standard recess in crankshaft.
* With 15mm spigot
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate2.0 or 2.3 Ford Duratec lightweight steel flywheel to suit Twin plate 7 1/4″ paddle clutch. With integral starter ring (ring gear is machined into the flywheel)
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
Products that you might find interesting
Pinto or Cosworth to Borg Warner T5 Bellhousing
Pinto or Cosworth to Borg Warner T5 Bellhousing
Pinto or Cosworth to Borg Warner T5 Bellhousing
Pinto or Cosworth to Borg Warner T5 BellhousingThis bellhousing will mate the Ford 2.0L OHC (Pinto) or naturally aspirated Cosworth Engines to the Borg Warner T5 (2WD Cosworth) gearbox.
Toyota 4AGE to Ford Gearbox Bellhousing
Toyota 4AGE to Ford Gearbox BellhousingThis bellhousing will mate the Toyota 4AGE engine, in either 16 valve or 20 valve format, to the Ford Type E (Rocket) 4 speed or Ford Type 9 (Sierra) 5 speed gearbox.
Sierra Direct Replacement Hydraulic Clutch Bellhousing
Sierra Direct Replacement Hydraulic Clutch Bellhousing
Sierra Direct Replacement Hydraulic Clutch Bellhousing
Sierra Direct Replacement Hydraulic Clutch BellhousingThis bellhousing is a direct replacement for the cast iron Ford Sierra item. Based on our Cable Clutch Bellhousing but redesigned for hydraulic actuation, retaining the cable release arm.
RS2000 Type Bellhousing (cable clutch)
RS2000 Type Bellhousing (cable clutch)This is an accurate reproduction of the Ford RS2000 (MkI & MkII Escort) alloy bellhousing with optional quick release facility.
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic ClutchThis slave cylinder fits directly inside our Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing. For use with a 0.625 inch (5/8″) master cylinder.
VW / Audi 1.8 Litre to Ford Type 9 Bellhousing
VW / Audi 1.8 Litre to Ford Type 9 Bellhousing
VW / Audi 1.8 Litre to Ford Type 9 Bellhousing
VW / Audi 1.8 Litre to Ford Type 9 BellhousingThis bellhousing will mate the Volkswagen, Audi, SEAT or Skoda 1.8 litre 20 valve turbocharged engines to the Ford Type 9 (Sierra) gearbox.
Upsell Products
Duratec Engine to Ford Gearbox Cable Clutch Bellhousing
Duratec Engine to Ford Gearbox Cable Clutch Bellhousing
Duratec Engine to Ford Gearbox Cable Clutch Bellhousing
Duratec Engine to Ford Gearbox Cable Clutch BellhousingThis bellhousing allows the 1.8l, 2.0l or 2.3l Duratec engine to be connected to the Ford Type E (Rocket 4 sp) and Type 9 (Sierra 5 sp) gearboxes using a cable clutch.
