Honda K20 or K24 ARP flywheel bolt set
Honda K20 or K24 ARP flywheel bolt set
£66.00
For Honda K20 engines.
Suitable for the following flywheels:
Honda K20 Lightweight Steel Flywheel – Standard Clutch Plate
Honda K20 Lightweight Steel Flywheel – 7 1/4″ 184mm Race Clutch Plate
Additional information
| Weight | 0.2 kg |
|---|
Related Products
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate2.0 or 2.3 Ford Duratec lightweight steel flywheel to suit Twin plate 7 1/4″ paddle clutch. With integral starter ring (ring gear is machined into the flywheel)
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
Products that you might find interesting
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 GearboxThis slave cylinder fits directly inside our VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing or VW / Audi 1.8 Litre to Ford Type 9 Bellhousing.
For use with a 0.625 inch (5/8″) master cylinder.
Spigot bearing 10mm internal diameter
Spigot bearing 10mm internal diameterConverts the Zetec SE / Sigma 1.7 VCT crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Rocket input shaft. Fits in standard recess in crankshaft.
Spigot bearing
Spigot bearingConverts crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Borg Warner T5* input shaft. Fits in standard recess in crankshaft.
* With 15mm spigot
10mm Cap Head Bolts (4)
10mm Cap Head Bolts (4)4 10mm x 1 1/2mm pitch cap head bolts for when a quick release bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox externally straight through the original tapped 12mm holes of the Ford gearbox and screwed into the 10mm tapped holes of the quick release bellhousing.
Borg Warner T5 Hydraulic Release Bearing Kit
Borg Warner T5 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing T5 gearbox. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
Fine Cap Head Bolts (4)
Fine Cap Head Bolts (4)4 12mm x 1 1/2mm pitch x 40mm long fine cap head bolts for when a standard fitment bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox internally.
